Exactly How to Install a Bath Tub in Your Bathroom
Exactly How to Install a Bath Tub in Your Bathroom
Blog Article
We have found the article on How to Install a Bathtub Yourself below on the net and figured it made sense to discuss it with you on my blog.
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately tough task. If the old bathtub is readily available, the job can relocate easily; if you need to open a wall to remove the old tub as well as place the brand-new bath tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified on your own for the work and also fit trying it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Opportunities are you might require a specialist plumber to make tube links.
This write-up will help you install a new bathtub in your bathroom if you have actually currently acquired a brand-new bathtub as well as don't need to change the arrangement of your previous water supply pipelines.
Your devices and also product checklist ought to comprise the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water supply. After doing so, activate the faucets to drain any water remaining in the system. The procedure of eliminating the existing taps can be quite bothersome because of the limited accessibility that is typically the case.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin making sure that the washing machines are in location in between the tap as well as the sink. Secure the tap in position with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be linked to the faucet ends initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Tub
Making use of the two wood boards under its feet, position the bathtub in the called for position. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to ensure that the tub is leveled all round. This can be accomplished by examining the level and changing the feet on the bath tub until the spirit level reviews level.
To install faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the other faucet.
Activate the water supply as well as inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill up the tub as well as additionally examine the overflow outlet as well as the typical electrical outlet for leaks.
Lastly, deal with the bathroom paneling as described in the producer's instruction manual. Tiling as well as sealing around the tub must wait up until the tub has been utilized a minimum of once as this will settle it into its final position.
Preparing for the Installation
Firstly, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets device to avoid stress on the tub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final placement.
Tiling Around the Tub
In the location where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack an inflexible seal, triggering the water to pass through the wall surface between the bathroom and the tiling, bring about problems with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your components and installations. They are offered in tubes and also cartridges, as well as are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to allow for the motion experienced when the tub remains in use. The sealer can crack rather early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about How to Install a Bathtub Yourself? Try leaving feedback further down. We would be glad to find out your reactions about this blog posting. We are looking forward that you come back again before long. Don't hesitate to take the time to distribute this blog if you liked it. I enjoy reading our article about How to Install a Bathtub Yourself.
Contact Us Report this page